slave controller had alarm and its fiber and scsi ports are down . after repluged , it become up and ports become HDD in 9 disk enclosures status become failed
virtula disk status is good and presented good and writable
↧
EVA P6500 *SC Event Code: 06304e13 - A controller has detected only one port of all devices in an
↧
HPE SN3000B Fibre Channel Switch
Hi everyone!
I'm a newbie!
I want to ask about functionality of SFP port on HPE SN3000B.
I want to know SFP port on SN3000B can be hot-swap or not? I read from spec but didn't saw anything relate sfp support hot-swapable.
And can be configure 1 + 1 redundancy or not?
Thanks a lot!
↧
↧
HP EVA HS340 Add disks to default disk group CLI
Hi Folks
I have a P6000 EVA storage with a default disk group having 15 drives, and 6 driver ungrouped. I want to add 6 drives into the default disk group, however command view is not accesible via VPN. Can anymore tell us the command to add the disks to the disk group?
↧
Looking for HP Disk Sanitize
Hello,
I am looking for HP Disk Sanitzer . Does anyone have a link to this?
Thank you.
↧
Need advice on changing a failed disk
Hello everyone,
I'm currently working with a StorageWorks P6300 EVA with a failed disk and I'm seeking some advice on the correct method of replacing it.
The failed disk (2TB) is part of a 6 disk group (please see the attached pictures for group & disk details).
I also have a few ungrouped 2TB drives already in the EVA that can be used as replacements.
From my research, I'm seeing a variety of methods to replace a drive but I am unsure which of them is the correct way to go.
Is the replacement method as follows?
- Ungrouping the failed drive
- Choosing to ungroup in the background and allowing that to finish
- Group one of the unused 2TB drives in the EVA into the disk group
- Click the Remove button on the failed disk
I would appreciate some feedback on the above.
Best Regards
↧
↧
Understanding Uninitializing in the HP P6000 Control Panel
Hi, and thanks for taking your time to read this.
Here at our company we have recieved a HP rack with an HSV300 and two AG638B fiber channel enclosures. As our policy is to zero wipe all hard drives we sell, we needed to make sure we are wiping these fiber channel drives.
So far:
Both controllers are connected to the FC enclosures. There are 8 FC drives in each enclosure. We hooked up a laptop with a ethernet cable to the management module, and connected to the HP p6000 control screen. We log in and am able to view the drives in cammand view. Then we went back and chose the "Uninitialize Drives" option, and went ahead with it. "Operation Sucessful" immediatly pops up.
I just wanted to know exactly how uninitialization works. Is it actually zeroing all the drives? Or is it a simple format? We cannot deem drives being "wiped" if they are not zeroed.
Now if they are not being zeroed, is there any other possible way to wipe the drives? Fiber Channel is really different from the usual SATA and SAS drives....
Any other tips or wisdom is welcome. Have a nice day.
↧
Replace battery of eva 6400
Hello,
I have an EVA6400 (HSV400), one of the batteries of the cache controllers is in fault.
I tried to replace it with one with the spare number 512735-001.
I bought 3 batteries but none of them appears in good condition.
The P/N is the same in all (AD262B), and the only difference is the Rev in the original is D4 but in the new ones it is A3.
The new batteries are refurbished, I do not know if there will be any expiration mark.
You could help me.
Thank you
↧
Leveling is stuck at 7%
History:
EVA 4400
I'm new to EVAs. Didn't know they existed until 3 months ago. Now I "support" 3.
One of them had a drive fail. During the leveling process 4 other drives failed. After that leveling process completed I replaced 3 of the 4 drives. (all we had) The machine started leveling again and spitting out this error:
A hardware failure has occured in this disk group. The advanced virtualization features on your system have prevented any data from being lost, but the level of prtection in the disk group is degraded. Please repair the hardware failure as soon as possible etc etc etc etc.. This message pops up every 5 seconds or so.
I was tol do wait forthe leveling process to complete before making any further changes. It has been 3 weeks of leveling and the percentage was stuck at 6%. for 2 of the 3 weeks. Yesterday it jumped to 7%. Do I need to wait 93 weeks for it to finish?
↧
EVA4400 Firmware Needed
Hi!
We have 2 EVA4400 (1 EVA4400 and 1 EVA4400 Embedded Switch) that were under a HP contract until HP stopped supporting it a few years ago. We had both EVA's at 11300000 (controllers), but had to replace a controller that has 11200000. Would like to upgrade, but don't have the firmware file anymore. Thoughts?
Thanks,
Emil
↧
↧
HP P6000 Thin Provisioning Software license
Hi,
I have upgraded an EVA4400 to HP P6000 and following the upgrade manual it says that in order to obtain the Thin Provisioning license I need to go to http://www.software.hp.com/kiosk which is no longer available. Does anybody know how can I obtain the license upgrade for this feature?
Thanks!!
↧
Migrate from one EvA Server to another
We have HP P6000 CV 10.2 installed on a Windows Server 2008 R2 machine managing 3 storage systems. We would like to move to a Windows Server 2012 R2 with HP 6000 CV 10.3. I cannot seem to find any documentation or instructions about migrating to a new server.
So two questions:
1. Where can I find documentation about moving control of an EVA storage system to a new server?
2. Will changing the server that manages these systems take them offline?
↧
open port at firewall for EVA P6000
Hi
There are three EVA P6000s and customer did set IP addresses with Management Module.
Customer tried to access all EVAs at management PC through Chrome but he can’t access.
He checked ports blocked at firewall and he found he need to open ports such as 34562, 52705 and 56438.
After opening customer can access all EVAs. The three EVAs uses each different port.
Customer’s questions are “Why should customer open three separate ports such as 34562, 52705 and 56438 ?”
and “Are there any port policy with EVA for firewall ?”.
Port permitted at customer firewall :
2372, 2374, 5988, 5989, 2376, 2377, 2379, 860, 2386, 3202
Controller firmware version : 11200000
Command view EVA version : 10.3
↧
EVA 8400 - After adding new disk enclosure - not updated firmware for I/O module
Hello!
I have EVA 8400 in the productive mode (2 controllers and 16 disk enclosures). I need to add 2 new disk enclosures ONLINE. I used documentation https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-c01867959 (page 27). When I break loop number 1 and connect new disk enclosures, I get I/O Module A Operational state - Loading firmware... The firmware for I/O Module is not updated and I can't connect second loop - I'm afraid of losing data or tearing data off...
In lof file i get next error:
SC Event Code: 066df308 - The controller cannot continue to codeload any Enclosure hardware requiring updates until backend redundancy is restored.
Please help someone solve this problem. Thanks
↧
↧
HP EVA P6500 Storage problem connect CV.
I have a ProLiant BL460c G7 in BladeSystem c7000 Enclosure G2. As well as HP StorageWorks 8/24 San Switch. The server is Windows Server 2008 and HPP600 Command View Software. The problem is that I cannot connect to EVA. (No storage systems are visible from this instance ....) How to understand what is wrong?
↧
EVA 8400 show warning symbol and Condition status is Populated ( Data Disk )
Dear All,
recently i'm facing problem with EVA8400, currently this is my first experience with EVA8400 unit..
I look warning symbol at enclosure 13 and Bay 1. and i look status condition operational state is Populated ( Data disk) with warning symbol . Please see attachment.
What the meaning of this, and what can i do to resolved it .
Thanks for your help.
↧
EVA 6400 BOOT ERROR
I have one EVA 6400 that won't boot properly. I've connected to the MFG port and recieved the following. Any suggestions for a solution?
Build configuration information :
Baselevel ID : CR2094
Baselevel Date : 01/24/12 00:05:31
Image built by : formal
Software Version : 10100000
Build Environment : delp
IGNORE_PFG_COOKIE_CONTENTS = 00000000
IGNORE_PFG_COOKIE = 49500000
IGNORE_PFG_DELAY = 00000000
pfg_flag = 00000000
delay_seconds = 00000000
DBAT0 08000fff 08000002
DBAT1 10001fff 10000002
DBAT2 20003fff 20000002
DBAT3 40007fff 40000002
DBAT4 f8000007 f8000002
DBAT5 80007fff 80000000
DBAT6 00000000 00000000
DBAT7 fc0007ff fc00002a
Controller WWID is 5005-08B4-000C-C9BA
Controller SN is PAFUCB49SX5097
Controller Board Revision is B (2)
DebugFlags are 0x
PrintFlags are ffffx
Baselevel: CR2094delp (24-Jan-12 00:05:31)
?
SYS_get_IA: Index: 16(SPRITE), From: CARD
Image 16 at addr:0xfd400000 header FAILED EDC:45x!!
SYS_get_IA: Index: 02(OCP*), From: CARD
SYS_get_IA: Index: 06(SDC*), From: CARD
**** GLUE versions: 802
SYS_get_IA: Index: 15(Glue*), From: CARD
++S_irsa->do_print = 1 PC = 24dc20x
FM(tp)--Premature termination entry, type = 2. S_irsa->termination_rdy = 1.
FM(tp)--Premature termination tt = 0x8000. tc = 0x8302206c, sa = 0x6552b0
FM(tp)--Premature termination pc = 0x171440. ec = 0x196, mcsr = 0xdeaddead
Stack entry [0.] back chain = 006531CC link register = 00171410
Stack entry [1.] back chain = 0065321C link register = 0000959C
Stack entry [2.] back chain = 006532FC link register = 00006350
Stack entry [3.] back chain = 0065335C link register = 000001F0
FM(tp)--Premature termination preparation initiated
FM(tp)--fm_hs_check_lte_edc, LTEB rev: 249. at FE274800 [-1.] edc valid
FM(tp)*--fm_hs_check_lte_edc, LTEB rev unknown (0.) at FE204600 [0.]
FM(tp)*--fm_hs_check_lte_edc, LTEB rev unknown (0.) at FE208E00 [1.]
FM(tp)*--fm_hs_check_lte_edc, LTEB rev unknown (0.) at FE20D600 [2.]
FM(tp)*--fm_hs_check_lte_edc, LTEB rev unknown (0.) at FE211E00 [3.]
FM(tp)*--fm_hs_check_lte_edc, LTEB rev unknown (0.) at FE216600 [4.]
FM(tp)*--fm_hs_check_lte_edc, LTEB rev unknown (0.) at FE21AE00 [5.]
FM(tp)*--fm_hs_check_lte_edc, LTEB rev unknown (0.) at FE21F600 [6.]
FM(tp)*--fm_hs_check_lte_edc, LTEB rev unknown (0.) at FE223E00 [7.]
FM(tp)*--fm_hs_check_lte_edc, LTEB rev unknown (0.) at FE228600 [8.]
FM(tp)*--fm_hs_check_lte_edc, LTEB rev unknown (0.) at FE22CE00 [9.]
FM(tp)*--fm_hs_check_lte_edc, LTEB rev unknown (0.) at FE231600 [10.]
FM(tp)*--fm_hs_check_lte_edc, LTEB rev unknown (0.) at FE235E00 [11.]
FM(tp)*--fm_hs_check_lte_edc, LTEB rev unknown (0.) at FE23A600 [12.]
FM(tp)*--fm_hs_check_lte_edc, LTEB rev unknown (0.) at FE23EE00 [13.]
FM(tp)*--fm_hs_check_lte_edc, LTEB rev unknown (0.) at FE243600 [14.]
FM(tp)*--fm_hs_check_lte_edc, LTEB rev unknown (0.) at FE247E00 [15.]
FM(tp)*--fm_hs_check_lte_edc, LTEB rev unknown (0.) at FE24C600 [16.]
FM(tp)*--fm_hs_check_lte_edc, LTEB rev unknown (0.) at FE250E00 [17.]
FM(tp)*--fm_hs_check_lte_edc, LTEB rev unknown (0.) at FE255600 [18.]
FM(tp)*--fm_hs_check_lte_edc, LTEB rev unknown (0.) at FE259E00 [19.]
FM(tp)*--fm_hs_check_lte_edc, LTEB rev unknown (0.) at FE25E600 [20.]
FM(tp)*--fm_hs_check_lte_edc, LTEB rev unknown (0.) at FE262E00 [21.]
FM(tp)*--fm_hs_check_lte_edc, LTEB rev unknown (0.) at FE267600 [22.]
FM(tp)*--fm_hs_check_lte_edc, LTEB rev unknown (0.) at FE26BE00 [23.]
FM(tp)--fm_hs_process_lte--Storage System resync not in progress
FM(tp)--fm_hs_process_lte--FM_tps_get()=FM_TP_STATE_INITIATED
FM(tp)--fm_hs_process_lte--In Process Data
FM(tp)--fm_hs_process_lte--Termination Code = 0x8302206c,
FM(tp)--fm_hs_process_lte--Trap Type = 0x00008000,
FM(tp)--fm_hs_process_lte--Exception Vector = 0x00000196,
FM(tp)--fm_hs_process_lte--Program Counter = 0x00171440,
FM(tp)--fm_hs_process_lte--PTO = 0x00000000,
FM(tp)--fm_hs_process_lte--Glue Reset Input = 0x00000000,
FM(tp)--fm_hs_process_lte--Glue Reset Disable= 0x00000000,
FM(tp)--fm_hs_process_lte, LTE in NV is good
FM(tp)*--fm_hs_process_lte, status: 10. good_entries: 0. index: 0.
FM(tp)--fm_hs_process_lte, MRU ltesp->ltea[0.].u.data.ltei.lter.seq = 0.,
ltesp->ltea[0.].u.data.ltei.lter.termination_event.u.code = 8302206C
FM(tp)--fm_hs_process_lte, good_entries: 1. S_fm.mru_index: 0.
FM(tp)--fm_hs_process_lte, S_fm.flags.all_ltes_used 0
FM(tp)*--fm_hs_process_lte, Minimal Participation set by Termination Code: 0x8302206c
FM(tp)--Glue Minor Revision: 0.(00), Major Revision: 0.(00)
FM(tp)--*** Program Exception (FM_TRAP_TYPE_USER): 8302206c
FM(tp)--Controller Operation Terminated:
FM(tp)-- Uptime: 177931305.
FM(tp)-- Termination Time: '17-NOV-1858 00:00:24'
FM(tp)-- TerminationCode:8302206C PC:00171440 Baselevel:'CR2094'
FM(tp)-- Env:'delp', DebugFlags:0x0, PrintFlags:0xFFFF
FM(tp)-- Software Version: '10100000', Image Type: 'PRODUCT'
FM(tp)-- Model: 'HSV400', Mode: 'Secondary'
FM(tp)-- Process: 'unknown'
FM(tp)-- TP[0.]: 00000800 TP[1.]: 00198034
FM(tp)-- TP[2.]: 00000007 TP[3.]: 0000000A
FM(tp)-- TP[4.]: 070A0110 TP[5.]: 007A092C
FM(tp)-- TP[6.]: C0000000 TP[7.]: 00000000
FM(tp)-- TP[8.]: 00000000 TP[9.]: 00000000
FM(tp)-- TP[10.]: 00000043 TP[11.]: 00000000
FM(tp)-- Stack information:
++S_irsa->do_print = 2 PC = 22cb28x
Stack depth = 4. Initial stack pointer = 006531CC
Stack entry [0.] back chain = 0065321C link register = 00171440
Stack entry [1.] back chain = 006532FC link register = 0000959C
Stack entry [2.] back chain = 0065335C link register = 00006350
Stack entry [3.] back chain = 00000000 link register = 000001F0
S_irsa->do_print-- = 1 PC = 22cc24x
FM(tp)-- Exception save area information at 0x006552B0:
R0: 00000000 R1: 006531CC R2: 00542370 R3: 285AA961
R4: 00000000 R5: 00000000 R6: 285AA961 R7: 00000000
R8: 00000014 R9: 00000044 R10: 0000005C R11: 0000005C
R12: 0000005C R13: 0062DFF0 R14: 00000000 R15: 00620000
R16: 00000000 R17: 00000000 R18: 00000000 R19: 0065331C
R20: 00000000 R21: 10D69E2F R22: FE2A00E4 R23: 0067A1C4
R24: 00000030 R25: 0079F59C R26: 0079F380 R27: 007A092C
R28: 01EACFE0 R29: 1FFF0000 R30: 00000000 R31: 00659370
SRR0: 00171440 SRR1: 00020030 CR: 20000400 XER: 00000000
na1: 00000000 CTR: 00000000 LR: 00171430 Ecde: 00000196
Opt1: DEADDEAD Opt2: DEADDEAD na2: DEADDEAD na3: DEADDEAD
FM(tp)--Termination operations completed, not restarting
FM(tp)--safe_exit = 1. (00000001)
FM(tp)--Entering fm_fatal_crash.
The processor on this controller doesn't understand dbg_map_dbat2()
EXEC_ONLY monitor for the Classic PowerPC Enterprise Controller
Version 01.09
Copyright (c) 2001-2011, Hewlett-Packard Company
:
↧
EVA4400 files for Update
Hello.
I'm upgrading a StorageWorks HSV300 (EVA4400) and I'm having trouble finding the files to download.
I would like some help on how to find the files to update firmware and controllers.
Thank you very much in advance.
↧
↧
EVA4400 files for Update
Hello.
I'm upgrading a StorageWorks HSV300 (EVA4400) and I'm having trouble finding the files to download.
I would like some help on how to find the files to update firmware and controllers.
Thank you very much in advance.
↧
EVA4400 doesn't show disks at Command View
Hello everyone,
I am a trainee in a small IT-Service company. We have a EVA4400 with 2 disk shelfs and I am trying to make the whole thing work. What I already did:
- installed the EVA and the shelfs in a server rack
- connected them with a loop
- power on/access via web interface (of the management module)
-did the whole network configuration and so on...
- installed 8 disks (4x 300 GB and 4x 146 GB)
The problem is, that after the initialization the folloing error message appears:
'Operation failed! Building View List Object - Failed.'
My problem is, that I can't see the list of disks in the Command View, after I initialzied it. Instead I get an Internal System Management Error, which says, that the storage system isn't able to communicate with its management module.
In addition to that, a led of controller 2 is flashing orange, but I can't imagine, that this is part of my problem, because there are 2 controllers and one seems to work normally.
I would be happy if you guys had any ideas! :)
Marcel
↧
Command View EVA 10.x
Does anyone have CommandView 10.3.x installed on a Windows 2016 Server. Any issues installing or running it on 16?
↧